enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Threaded insert - Wikipedia

   en.wikipedia.org/wiki/Threaded_insert

   TIME-SERT insert. A threaded insert, also known as a threaded bushing, is a fastener element that is inserted into an object to add a threaded hole. [1] They may be used to repair a stripped threaded hole, provide a durable threaded hole in a soft material, place a thread on a material too thin to accept it, mold or cast threads into a work piece thereby eliminating a machining operation, or ...

3. Giubo - Wikipedia

   en.wikipedia.org/wiki/Giubo

   A driveshaft coupling. Note the split damage beginning to appear, likely due to the large axial displacement. A giubo. A giubo (/ ˈ dʒ uː b oʊ / JOO-boh; etymology: giunto Boschi, "Boschi joint"), also known as a 'flexdisc', and sometimes misspelled as guibo, is a flexible coupling used to transmit rotational torque between the drive shaft and the companion flange on mechanical devices ...

4. Drill bushing - Wikipedia

   en.wikipedia.org/wiki/Drill_bushing

   Customary bushings are specified using the following specification layout: [3] ID-Type-OD-Length. Where the ID is specified as a decimal, drill letter size, drill number size, or fraction; the OD is an integer that relates to a multiple of a 1 ⁄ 64 th of an inch (0.40 mm); the length is an integer that relates to a multiple of a 1 ⁄ 16 th

5. Screw - Wikipedia

   en.wikipedia.org/wiki/Screw

   A machine screw or bolt is usually a smaller fastener (less than 1 ⁄ 4 inch (6.35 mm) in diameter) threaded the entire length of its shank that usually has a recessed drive type (slotted, Phillips, etc.), usually intended to screw into a pre-formed thread, either a nut or a threaded (tapped) hole, unlike a wood or self-tapping screw. Machine ...

6. List of screw and bolt types - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_and_bolt_types

   The screw itself should be drilled a minimum of 1" into the concrete to hold effectively and a maximum of 1-3/4" or the threads will wear and will lose holding power. Ideally 1-1/4" to 1-1/2" of screw thread in the concrete. [1] So for example, if a 1/2" board is being screwed onto the concrete, a 1-3/4" to 2" concrete screw should be used ...

7. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   The standard designation for a UTS thread is a number indicating the nominal (major) diameter of the thread, followed by the pitch measured in threads per inch.For diameters smaller than ⁠ 1 / 4 ⁠ inch, the diameter is indicated by an integer number defined in the standard; for all other diameters, the inch figure is given.

8. Plain bearing - Wikipedia

   en.wikipedia.org/wiki/Plain_bearing

   A flanged bushing is a sleeve bushing with a flange at one end extending radially outward from the OD. The flange is used to positively locate the bushing when it is installed or to provide a thrust bearing surface. [9] Sleeve bearings of inch dimensions are almost exclusively dimensioned using the SAE numbering system.

9. National pipe thread - Wikipedia

   en.wikipedia.org/wiki/National_pipe_thread

   The half-angle (between the taper surface and the axis of the pipe) is arctan(1 ⁄ 32) ≈ 1.7899° ≈ 1° 47′. The standard for Nominal Pipe Size (often abbreviated NPS, which should not be confused with the abbreviation NPS for the straight thread form standard) is loosely related to the inside diameter of Schedule 40 series of sizes.