enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25).

3. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Below is a comprehensive drill and tap size chart for all drills and taps, ... Many thread sizes have several possible tap drills, ... M2×0.4 2.2 mm 1.6129 0.06350 ...

4. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   Unified Miniature Screw Threads: V Thread Form: 0.60 UNM ANSI/ASME B1.11-1958 (R2016) Microscope Objective Thread: V Thread Form ASME B1.13M-2005 (R2015) Metric Screw Threads: M Profile: V Thread Form ASME B1.15-1995 (R2003) Unified Inch Screw Threads (UNJ Thread Form) V Thread Form ASME B1.20.1-2013: Pipe Threads, General Purpose (Inch) Pipe ...

5. Preferred metric sizes - Wikipedia

   en.wikipedia.org/wiki/Preferred_metric_sizes

   Machine screws with different thread diameters Hex key set with metric sizes from 2 mm to 10 mm according to sizes for use with ISO 262 screw sizes (except 3.5 mm for M6 internal set screw) For each size bolt or screw and type of head, there is a corresponding size driver prescribed by various ISO standards, including:

6. ISO 965 - Wikipedia

   en.wikipedia.org/wiki/ISO_965

   ISO 965 (ISO general purpose metric screw thread—tolerances) is an International Organization for Standardization (ISO) standard for metric screw thread tolerances. [1] It specifies the basic profile for ISO general purpose metric screw threads (M) conforming to ISO 261. [2] The tolerance system refers to the basic profile in accordance with ...

7. Wrench size - Wikipedia

   en.wikipedia.org/wiki/Wrench_size

   Sizes that may interchange, depending on the precision needed, include 2 mm (close to 5 ⁄ 64 inch (1.98 mm)), 4 mm (close to 5 ⁄ 32 inch (3.97 mm)) and 8 mm (close to 5 ⁄ 16 inch (7.94 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

8. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   Imperial Metric fastening size conversion charts; International Thread Standards; Conversion chart Whitworth/BSF/AF and metric Archived 2 May 2010 at the Wayback Machine; Spanner Jaw Sizes Additional information and spanner jaw size table. Unified Screw Threads Series; ASME B1.1-2003 Unified Inch Screw Threads, (UN and UNR Thread Form)

9. List of screw and bolt types - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_and_bolt_types

   The term fine adjustment screw typically refers to screws with threads from 40–100 TPI (Threads Per Inch) (0.5 mm to 0.2 mm pitch) and ultra fine adjustment screw has been used to refer to 100–254 TPI (0.2 mm to 0.1 mm pitch). These screws are most frequently used in applications where the screw is used to control fine motion of an object.