enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25).

3. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   V Thread Form ISO 261:1998: ISO general purpose metric screw threads—General plan: V Thread Form: M6x1 ISO 262:1998: ISO general purpose metric screw threads—Selected sizes for screws, bolts and nuts: V Thread Form ISO 724:1993: ISO general-purpose metric screw threads—Basic dimensions: V Thread Form ISO 725:2009: ISO inch screw threads ...

4. British Association screw threads - Wikipedia

   en.wikipedia.org/wiki/British_Association_screw...

   BS 93:1951 — Specification for British Association (B.A.) screw threads with tolerances for sizes 0 B.A. to 16 B.A. BS 93:2008 — British Association (B.A.) screw threads — Requirements The angle of the thread is 47.5° [ 4 ] : 2 and the depth of thread is 0.6 times the pitch with rounded tops and bottoms.

5. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   The standard designation for a UTS thread is a number indicating the nominal (major) diameter of the thread, followed by the pitch measured in threads per inch.For diameters smaller than ⁠ 1 / 4 ⁠ inch, the diameter is indicated by an integer number defined in the standard; for all other diameters, the inch figure is given.

6. ASTM A325 - Wikipedia

   en.wikipedia.org/wiki/ASTM_A325

   It defines mechanical properties for bolts that range from 1 ⁄ 2 to 1 + 1 ⁄ 2 inches (13 to 38 mm) in diameter. [1] The equivalent metric standard is ASTM A325M, which is titled Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength. It defines mechanical properties for sizes M12–36. [2]

7. United States Standard thread - Wikipedia

   en.wikipedia.org/wiki/United_States_Standard_thread

   The thread form is defined by flats at the tip and root of the thread form. This flat length is defined as the pitch divided by eight. The thread depth, which is from flat to flat is 0.6495 times the pitch. [4] For 1 ⁄ 4-inch (6.4 mm) screws and larger, the pitch is defined as: = +

8. ISO 898 - Wikipedia

   en.wikipedia.org/wiki/ISO_898

   This standard is the origin for other standards that define properties for similar metric fasteners, such as SAE J1199 and ASTM F568M. [1] It is divided into five (nonconsecutive) parts: 1. Bolts, screws and studs with specified property classes – Coarse thread and fine pitch thread [2] 2. Nuts with specified proof load values – Coarse ...

9. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.