enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   The major diameter may be slightly different from the shank diameter, which is the diameter of the unthreaded part of the screw. The diameters are sometimes given approximately in fractions of an inch (e.g. the major diameter of a #6 screw is 0.1380 in, approximately 9 ⁄ 64 in = 0.140625 in. The pitch P is the distance between thread peaks.

3. British Standard Pipe - Wikipedia

   en.wikipedia.org/wiki/British_Standard_Pipe

   British Standard Pipe Parallel Thread Dimensions; British Standard Pipe Taper Thread Dimensions Archived 2017-09-27 at the Wayback Machine; BSP Thread Charts and Diagrams, showing dimensions of tubing and fittings; ISO 7-1:1994; ISO 7-2:2000; ISO 228-1:2000; ISO 228-2:1987; Parallel pipe threads G; Parallel pipe threads PF

4. AN thread - Wikipedia

   en.wikipedia.org/wiki/AN_thread

   AN sizes range from -2 (dash two) to -32 in irregular steps, with each step equating to the OD (outside diameter) of the tubing in 1 ⁄ 16-inch increments. Therefore, a -8 AN size would be equal to 1 ⁄ 2-inch OD tube. However, this system does not specify the ID (inside diameter) of the tubing because the tube wall can vary in thickness ...

5. National pipe thread - Wikipedia

   en.wikipedia.org/wiki/National_pipe_thread

   The taper rate for all NPT threads is 1 inch of diameter in 16 inches of length (3 ⁄ 4 inch per foot or 62.5 millimeters per meter) measured by the change of diameter (of the pipe thread) over distance of thread. The half-angle (between the taper surface and the axis of the pipe) is arctan(1 ⁄ 32) ≈ 1.7899° ≈ 1° 47′.

6. Tube (fluid conveyance) - Wikipedia

   en.wikipedia.org/wiki/Tube_(fluid_conveyance)

   Both pipe and tube imply a level of rigidity and permanence, whereas a hose is usually portable and flexible. A tube and pipe may be specified by standard pipe size designations, e.g., nominal pipe size, or by nominal outside or inside diameter and/or wall thickness. The actual dimensions of pipe are usually not the nominal dimensions: A 1-inch ...

7. Width across flats - Wikipedia

   en.wikipedia.org/wiki/Wrench_size

   A few sizes are close enough to interchange for most purposes, such as 19 mm (close to 3 ⁄ 4 inch (19.05 mm)), 8 mm (close to 5 ⁄ 16 inch (7.94 mm)) and 4 mm (close to 5 ⁄ 32 inch (3.97 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

8. AOL Mail

   mail.aol.com/d?reason=invalid_cred

   Get AOL Mail for FREE! Manage your email like never before with travel, photo & document views. Personalize your inbox with themes & tabs. You've Got Mail!

9. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.