enow.com Web Search

  1. Ad

    related to: pipe sizes inch to mm

Search results

  1. Results from the WOW.Com Content Network
  2. Nominal Pipe Size - Wikipedia

    en.wikipedia.org/wiki/Nominal_Pipe_Size

    Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

  3. British Standard Pipe - Wikipedia

    en.wikipedia.org/wiki/British_Standard_Pipe

    In the modern standard metric version, it is simply a size number, where listed diameter size is the major outer diameter of the external thread. For a taper thread, it is the diameter at the "gauge length" (plus/minus one thread pitch) from the small end of the thread.

  4. Copper tubing - Wikipedia

    en.wikipedia.org/wiki/Copper_tubing

    For example, DN20 is the size for copper pipe with an outside diameter of 19.05 mm or 3 ⁄ 4 inch. While pipe sizes in Australia are inch-based, they are classified by outside rather than inside diameter (e.g., a nominal 3 ⁄ 4 inch copper pipe in Australia has measured diameters of 0.750 inches outside and 0.638 inches inside, whereas a ...

  5. National pipe thread - Wikipedia

    en.wikipedia.org/wiki/National_pipe_thread

    pipe size Thread density Thread pitch P Hand-tight engagement [6] Effective thread [6] Overall length L 4 [6] Actual outside diameter D Tap drill; Length L 1 Turns Diameter E 1 Length L 2 Turns Diameter E 2; inch inch −1 inch mm inch inch inch inch inch inch mm inch mm 1 ⁄ 16: 27 0.03703704 0.9407 0.1600: 4.32: 0.28118 0.2611: 7.05: 0.2875 ...

  6. Pipe (fluid conveyance) - Wikipedia

    en.wikipedia.org/wiki/Pipe_(fluid_conveyance)

    Pipe sizes can be confusing because the terminology may relate to historical dimensions. For example, a half-inch iron pipe does not have any dimension that is a half inch. Initially, a half inch pipe did have an inner diameter of 1 ⁄ 2 inch (13 mm)—but it also had thick walls. As technology improved, thinner walls became possible, but the ...

  7. Iron pipe size - Wikipedia

    en.wikipedia.org/wiki/Iron_pipe_size

    During the IPS period, pipes were cast in halves and welded together, and pipe sizes referred to the inside diameters. [1] The inside diameters under IPS were roughly the same as the more modern Ductile Iron Pipe Standard (DIPS) and Nominal Pipe Size (NPS) Standards, and some of the wall thicknesses were also retained with a different ...

  8. Ductile iron pipe - Wikipedia

    en.wikipedia.org/wiki/Ductile_iron_pipe

    Ductile iron pipe is sized according to a dimensionless term known as the Pipe Size or Nominal Diameter (known by its French abbreviation, DN). This is roughly equivalent to the pipe's internal diameter in inches or millimeters.

  9. Plastic pipework - Wikipedia

    en.wikipedia.org/wiki/Plastic_pipework

    Pipes, fittings, valves, and accessories make up a plastic pressure pipe system. The range of pipe diameters for each pipe system does vary. However, the size ranges from 12 to 400 mm (0.472 to 15.748 in) and 3 ⁄ 8 to 16 in (9.53 to 406.40 mm). Pipes are extruded and are generally available in: 3 m (9.84 ft), 4 m (13.12 ft), 5 m (16.40 ft ...

  1. Ad

    related to: pipe sizes inch to mm