enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Birmingham gauge - Wikipedia

   en.wikipedia.org/wiki/Birmingham_gauge

   The Birmingham gauge ranges from 5/0 or 00000, the lowest gauge number corresponding to the largest size of 0.500 inches (12.7 mm), to 36, the highest gauge number corresponding to the smallest size of 0.004 inches (0.10 mm). The increments between gauge sizes are not linear and vary. [2]

3. Iron pipe size - Wikipedia

   en.wikipedia.org/wiki/Iron_pipe_size

   During the IPS period, pipes were cast in halves and welded together, and pipe sizes referred to the inside diameters. [1] The inside diameters under IPS were roughly the same as the more modern Ductile Iron Pipe Standard (DIPS) and Nominal Pipe Size (NPS) Standards, and some of the wall thicknesses were also retained with a different ...

4. Nominal Pipe Size - Wikipedia

   en.wikipedia.org/wiki/Nominal_Pipe_Size

   Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

5. Tube (fluid conveyance) - Wikipedia

   en.wikipedia.org/wiki/Tube_(fluid_conveyance)

   A tube and pipe may be specified by standard pipe size designations, e.g., nominal pipe size, or by nominal outside or inside diameter and/or wall thickness. The actual dimensions of pipe are usually not the nominal dimensions: A 1-inch pipe will not actually measure 1 inch in either outside or inside diameter, whereas many types of tubing are ...

6. National pipe thread - Wikipedia

   en.wikipedia.org/wiki/National_pipe_thread

   pipe size Thread density Thread pitch P Hand-tight engagement [6] Effective thread [6] Overall length L 4 [6] Actual outside diameter D Tap drill; Length L 1 Turns Diameter E 1 Length L 2 Turns Diameter E 2; inch inch −1 inch mm inch inch inch inch inch inch mm inch mm 1 ⁄ 16: 27 0.03703704 0.9407 0.1600: 4.32: 0.28118 0.2611: 7.05: 0.2875 ...

7. Pipe (fluid conveyance) - Wikipedia

   en.wikipedia.org/wiki/Pipe_(fluid_conveyance)

   The number system, like Sch 40, 80, 160, were set long ago and seem a little odd. For example, Sch 20 pipe is even thinner than Sch 40, but same OD. And while these pipes are based on old steel pipe sizes, there is other pipe, like cpvc for heated water, that uses pipe sizes, inside and out, based on old copper pipe size standards instead of steel.

8. List of vacuum tubes - Wikipedia

   en.wikipedia.org/wiki/List_of_vacuum_tubes

   110–119 – Y8A 8-pin steel tube base; Rimlock B8A; 130–139 – Octal; 150–159 – German 10-pin with spigot; 10-pin glass with one big pin; Octal; 160–169 – Inline wire-ended Pencil tubes; Y8A 8-pin steel tube base; 170–179 – RFT 8-pin; RFT 11-pin all-glass gnome tube with one offset pin; 180–189 – Noval B9A; 190–199 ...

9. Hollow structural section - Wikipedia

   en.wikipedia.org/wiki/Hollow_structural_section

   In the recent past, HSS was commonly available in mild steel, such as A500 grade B. Today, HSS is commonly available in mild steel, A500 grade C. Other steel grades available for HSS are A847 (weathering steel), A1065 (large sections up to 50 inch sq made with SAW process), and recently approved A1085 (higher strength, tighter tolerances than ...