enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. Countersink - Wikipedia

    en.wikipedia.org/wiki/Countersink

    In manufacturing, a countersink (symbol: ⌵) is a conical hole cut into a manufactured object, or the cutter used to cut such a hole. A common use is to allow the head of a countersunk bolt , screw or rivet , when placed in the hole, to sit flush with or below the surface of the surrounding material (by comparison, a counterbore makes a flat ...

  3. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Below is a comprehensive drill and tap size chart for all drills and taps: Inch, imperial, and metric, up to 36.5 millimetres (1.44 in) in diameter. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.

  4. List of screw and bolt types - Wikipedia

    en.wikipedia.org/wiki/List_of_screw_and_bolt_types

    Nominal (thread) sizes range from 0.1875 to 0.375 in (4.763 to 9.525 mm) and lengths from 1.25 to 5 in (32 to 127 mm). Typically an installer uses a hammer drill to make a pilot hole for each concrete screw and a powered impact driver to drive the screw. The drill hole should be 1/2" longer than the depth penetration of the screw.

  5. List of thread standards - Wikipedia

    en.wikipedia.org/wiki/List_of_thread_standards

    ANSI/ASME B1.11-1958 (R2016) Microscope Objective Thread: V Thread Form ASME B1.13M-2005 (R2015) Metric Screw Threads: M Profile: V Thread Form ASME B1.15-1995 (R2003) Unified Inch Screw Threads (UNJ Thread Form) V Thread Form ASME B1.20.1-2013: Pipe Threads, General Purpose (Inch) Pipe Thread Form ANSI B1.20.3-1976 (R2013) Dryseal Pipe Threads ...

  6. Unified Thread Standard - Wikipedia

    en.wikipedia.org/wiki/Unified_Thread_Standard

    Even though #14 and #16 screws are still available, they are not as common as sizes #0 through #12. [citation needed] Sometimes "special" diameter and pitch combinations (UNS) are used, for example a 0.619 in (15.7 mm) major diameter with 20 threads per inch. UNS threads are rarely used for bolts, but rather on nuts, tapped holes, and threaded ODs.

  7. Engineering fit - Wikipedia

    en.wikipedia.org/wiki/Engineering_fit

    Engineering fits are generally used as part of geometric dimensioning and tolerancing when a part or assembly is designed. In engineering terms, the "fit" is the clearance between two mating parts, and the size of this clearance determines whether the parts can, at one end of the spectrum, move or rotate independently from each other or, at the other end, are temporarily or permanently joined.

  8. Counterbore - Wikipedia

    en.wikipedia.org/wiki/Counterbore

    In machining, a counterbore (symbol: ⌴) is a cylindrical flat-bottomed hole that enlarges another coaxial hole, or the tool used to create that feature. A counterbore hole is typically used when a fastener, such as a socket head cap screw or fillister head screw, is required to sit flush with or below the level of a workpiece's surface.

  9. Self-tapping screw - Wikipedia

    en.wikipedia.org/wiki/Self-tapping_screw

    The countersunk head has a Pozidriv recess. A self-tapping screw is a screw that can tap its own hole as it is driven into the material. More narrowly, self-tapping is used only to describe a specific type of thread-cutting screw intended to produce a thread in relatively soft material or sheet materials, excluding wood screws .