enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Many thread sizes have several possible tap drills, because they yield threads of varying thread depth between 50% and 100%. Usually thread depths of 60% to 75% are desired. People frequently use a chart such as this to determine the proper tap drill for a certain thread size or the proper tap for an existing hole.

3. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   Because only 5 ⁄ 8 of this height is cut, the difference between major and minor diameters is 5 ⁄ 4 × 0.8660 × P = 1.0825 × P, so the tap drill size can be approximated by subtracting the thread pitch from the major diameter.

4. List of screw and bolt types - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_and_bolt_types

   The screw itself should be drilled a minimum of 1" into the concrete to hold effectively and a maximum of 1-3/4" or the threads will wear and will lose holding power. Ideally 1-1/4" to 1-1/2" of screw thread in the concrete. [1] So for example, if a 1/2" board is being screwed onto the concrete, a 1-3/4" to 2" concrete screw should be used ...

5. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   Microscope Objective Thread: V Thread Form ASME B1.13M-2005 (R2015) Metric Screw Threads: M Profile: V Thread Form ASME B1.15-1995 (R2003) Unified Inch Screw Threads (UNJ Thread Form) V Thread Form ASME B1.20.1-2013: Pipe Threads, General Purpose (Inch) Pipe Thread Form ANSI B1.20.3-1976 (R2013) Dryseal Pipe Threads (Inch) Pipe Thread Form

6. Drill bit sizes - Wikipedia

   en.wikipedia.org/wiki/Drill_bit_sizes

   So a 1 / 2 in (12.7 mm) diameter drill will be able to drill a hole 4 + 1 / 2 in (114.3 mm) deep, since it is 9 times the diameter in length. A 1 / 8 in (3.175 mm) diameter drill can drill a hole 1 + 5 / 8 in (41.275 mm) deep, since it is 13 times the diameter in flute length. [3]

7. Preferred metric sizes - Wikipedia

   en.wikipedia.org/wiki/Preferred_metric_sizes

   [4] Machine screws with different thread diameters Hex key set with metric sizes from 2 mm to 10 mm according to sizes for use with ISO 262 screw sizes (except 3.5 mm for M6 internal set screw) For each size bolt or screw and type of head, there is a corresponding size driver prescribed by various ISO standards, including:

8. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   The standard designation for a UTS thread is a number indicating the nominal (major) diameter of the thread, followed by the pitch measured in threads per inch.For diameters smaller than ⁠ 1 / 4 ⁠ inch, the diameter is indicated by an integer number defined in the standard; for all other diameters, the inch figure is given.

9. British Standard Pipe - Wikipedia

   en.wikipedia.org/wiki/British_Standard_Pipe

   For a taper thread, it is the diameter at the "gauge length" (plus/minus one thread pitch) from the small end of the thread. The taper is 1:16, meaning that for each 16 units of measurement increase in the distance from the end, the diameter increases by 1 unit of measurement.