enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Width across flats - Wikipedia

   en.wikipedia.org/wiki/Width_across_flats

   A few sizes are close enough to interchange for most purposes, such as 19 mm (close to 3 ⁄ 4 inch (19.05 mm)), 8 mm (close to 5 ⁄ 16 inch (7.94 mm)) and 4 mm (close to 5 ⁄ 32 inch (3.97 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

3. Preferred metric sizes - Wikipedia

   en.wikipedia.org/wiki/Preferred_metric_sizes

   Machine screws with different thread diameters Hex key set with metric sizes from 2 mm to 10 mm according to sizes for use with ISO 262 screw sizes (except 3.5 mm for M6 internal set screw) For each size bolt or screw and type of head, there is a corresponding size driver prescribed by various ISO standards, including: Internal hex drive: ISO ...

4. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25). If the pitch is the normally used "coarse" pitch listed in ISO 261 or ...

5. List of screw and bolt types - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_and_bolt_types

   In 1913, Woolley and Meredith defined them like Anthony, but gave the following dimensions: hex head cap screws up to and including 7 ⁄ 16 inch (11.1125 mm) have a head that is 3 ⁄ 16 inch (4.7625 mm) larger than the shank diameter; screws greater than 1 ⁄ 2 inch (12.7 mm) in diameter have a head that is 1 ⁄ 4 inch (6.35 mm) larger than ...

6. Screw - Wikipedia

   en.wikipedia.org/wiki/Screw

   An assortment of screws, and a US quarter for size comparison A wood screw: a) head; b) non-threaded shank; c) threaded shank; d) tip The six classical simple machines. A screw is an externally helical threaded fastener capable of being tightened or released by a twisting force to the head.

7. Screw thread - Wikipedia

   en.wikipedia.org/wiki/Screw_thread

   A table of standard sizes for machine screws as provided by the American Screw Company of Providence, Rhode Island, USA, and published in a Mechanical Engineers' Handbook of 1916. Standards seen here overlap with those found elsewhere marked as ASME and SAE standards and with the later Unified Thread Standard (UTS) of 1949 and afterward.

8. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   ISO general purpose metric screw threads—General plan: V Thread Form: M6x1 ISO 262:1998: ISO general purpose metric screw threads—Selected sizes for screws, bolts and nuts: V Thread Form ISO 724:1993: ISO general-purpose metric screw threads—Basic dimensions: V Thread Form ISO 725:2009: ISO inch screw threads—Basic dimensions: V Thread ...

9. List of screw drives - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_drives

   In Japan, the male sizes are often designated as DTC-20, DTC-27, DTC-40 (discontinued) and DTC-45 corresponding to a respective screw head size of 3.2 mm, 4.6 mm, 6.4 mm and 7.7 mm; with the size of the screw measured across the widest portion of the mating part of the head. The most common sizes in use for consumer electronics are DTC-20 and ...