enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   The standard designation for a UTS thread is a number indicating the nominal (major) diameter of the thread, followed by the pitch measured in threads per inch.For diameters smaller than ⁠ 1 / 4 ⁠ inch, the diameter is indicated by an integer number defined in the standard; for all other diameters, the inch figure is given.

3. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Schematic of a machine tap. Below is a comprehensive drill and tap size chart for all drills and taps, imperial and metric, up to 36.5 millimetres (1.44 in) in diameter.. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.

4. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   V Thread Form: 1 ⁄ 4 ″-20 UNC #4-40 UNC ASME B1.5-1997 (R2014) Acme Screw Threads: Trapezoidal Thread Form: Tr 60×9 ANSI/ASME B1.9-1973 (R2017) Buttress Inch Screw Threads: Breech-Lock Thread Form: ASME B1.10M-2004 (R2014) Unified Miniature Screw Threads: V Thread Form: 0.60 UNM ANSI/ASME B1.11-1958 (R2016) Microscope Objective Thread: V ...

5. Thread pitch gauge - Wikipedia

   en.wikipedia.org/wiki/Thread_pitch_gauge

   A thread gauge, [1] also known as a screw gauge [2] or pitch gauge, [3] is used to measure the pitch or lead of a screw thread. Thread pitch gauges are used as a reference tool in determining the pitch of a thread that is on a screw or in a tapped hole. This tool is not used as a precision measuring instrument, rather it allows the user to ...

6. British Standard Pipe - Wikipedia

   en.wikipedia.org/wiki/British_Standard_Pipe

   For a taper thread, it is the diameter at the "gauge length" (plus/minus one thread pitch) from the small end of the thread. The taper is 1:16, meaning that for each 16 units of measurement increase in the distance from the end, the diameter increases by 1 unit of measurement.

7. Screw thread - Wikipedia

   en.wikipedia.org/wiki/Screw_thread

   The nominal diameter of Metric (e.g. M8) and Unified (e.g. 5 ⁄ 16 in) threads is the theoretical major diameter of the male thread, which is truncated (diametrically) by 0.866 ⁄ 4 of the pitch from the dimension over the tips of the "fundamental" (sharp

8. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25).

9. Thread angle - Wikipedia

   en.wikipedia.org/wiki/Thread_angle

   Acme thread [6] 29° ASME/ANSI B1.5-1988 [7] Metric trapezoidal threads [1] Tr 30° DIN 103 Buttress threads [6] S 45° DIN 2781 German buttress threads [6] S 30° DIN 513 Square threads [1] Sq 0° (parallel) ? Panzergewinde, "steel conduit thread" Pg 80° DIN 40430 British Association (BA) thread: BA 47° 30' = 47.5° BS 93:2008 Löwenherz ...