enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. National pipe thread - Wikipedia

   en.wikipedia.org/wiki/National_pipe_thread

   Because of the pipe wall thickness of Schedule pipe, the actual diameter of the NPT threads is larger than the Nominal Pipe Size diameter, and considerably so for small sizes. Pipe of a given size in a different Schedule than Schedule 40 provides a different wall thickness while maintaining the same outside diameter and thread profile as ...

3. Nominal Pipe Size - Wikipedia

   en.wikipedia.org/wiki/Nominal_Pipe_Size

   Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

4. British Standard Pipe - Wikipedia

   en.wikipedia.org/wiki/British_Standard_Pipe

   British Standard Pipe Parallel Thread Dimensions; British Standard Pipe Taper Thread Dimensions Archived 2017-09-27 at the Wayback Machine; BSP Thread Charts and Diagrams, showing dimensions of tubing and fittings; ISO 7-1:1994; ISO 7-2:2000; ISO 228-1:2000; ISO 228-2:1987; Parallel pipe threads G; Parallel pipe threads PF

5. ASTM A53 steel - Wikipedia

   en.wikipedia.org/wiki/ASTM_A53_steel

   Scope of ASTM A53 Standard ASTM A53 is standard specification for pipe, steel, black and hot dipped, zinc-coated, welded and seamless. This specification covers seamless and welded black and hot-dipped galvanized steel pipe in NPS 1⁄8 to NPS 26 [DN 6 to DN 650] (Note 1), inclusive, with nominal wall thickness (Note 2) as given in Table X2.2 ...

6. Standard dimension ratio - Wikipedia

   en.wikipedia.org/wiki/Standard_dimension_ratio

   Standard dimension ratio (SDR) is a method of rating a pipe's durability against pressure. The standard dimension ratio describes the correlation between the pipe dimension and the thickness of the pipe wall. [1] Common nominations are SDR11, SDR17, SDR26 and SDR35. Pipes with a lower SDR can withstand higher pressures.

7. Pipe (fluid conveyance) - Wikipedia

   en.wikipedia.org/wiki/Pipe_(fluid_conveyance)

   The pipe wall thickness has a variance of approximately 12.5 percent. In the rest of Europe pressure piping uses the same pipe IDs and wall thicknesses as Nominal Pipe Size, but labels them with a metric Diameter Nominal (DN) instead of the imperial NPS. For NPS larger than 14, the DN is equal to the NPS multiplied by 25.

8. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   Dryseal Pipe Threads (Inch) Pipe Thread Form ASME B1.20.7-1991 (R2013) Hose Coupling Screw Threads - Inch: Pipe Thread Form ASME B1.21M-1997 (R2013) Metric Screw Threads - MJ Profile: V Thread Form BS 84: Tables of BS Whitworth, BS Fine and BS Pipe Threads: V Thread Form (55°) 1 ⁄ 4 ″-20 BSW ISO 68-1:1998: ISO general purpose screw threads ...

9. Tube (fluid conveyance) - Wikipedia

   en.wikipedia.org/wiki/Tube_(fluid_conveyance)

   A tube and pipe may be specified by standard pipe size designations, e.g., nominal pipe size, or by nominal outside or inside diameter and/or wall thickness. The actual dimensions of pipe are usually not the nominal dimensions: A 1-inch pipe will not actually measure 1 inch in either outside or inside diameter, whereas many types of tubing are ...