enow.com Web Search

  1. Ads

    related to: main lug only vs mlo 5 bolt lock set 3 speed engine

Search results

  1. Results from the WOW.Com Content Network
  2. Chevrolet small-block engine (first- and second-generation)

    en.wikipedia.org/wiki/Chevrolet_small-block...

    The large-journal connecting rods were thicker (heavier) and used 3 ⁄ 8 in (9.5 mm) diameter cap-bolts to replace the small-journal's 11/32. 1968 blocks were made in 2-bolt and 4-bolt versions with the 4-bolt center-three main caps each fastened by two additional bolts which were supported by the addition of thicker crankcase main-web bulkheads.

  3. List of GM bellhousing patterns - Wikipedia

    en.wikipedia.org/wiki/List_of_GM_bellhousing...

    Jeep with GM Iron Duke inline 4 2.5L/151 in 3 (1980-1983). These use a Chrysler custom Torqueflite 904 automatic transmission with an integral Chevrolet bellhousing. Do not confuse with later AMC 2.5 L engine that uses GM small corporate pattern . Chevrolet Turbo-Thrift engine (post-1962)

  4. Engine configuration - Wikipedia

    en.wikipedia.org/wiki/Engine_configuration

    The Swashplate engine with the K-Cycle engine is where pairs of pistons are in an opposed configuration sharing a cylinder and combustion chamber. A Delta engine has three (or its multiple) cylinders having opposing pistons, aligned in three separate planes or 'banks', so that they appear to be in a Δ when viewed along the axis of the main-shaft.

  5. Main bearing - Wikipedia

    en.wikipedia.org/wiki/Main_bearing

    The lower half of the main bearings are typically held in place by 'bearing caps' which are secured to the engine block using bolts. The basic arrangement is for each bearing cap to have two bolts, but some engines may have four or six bolts per bearing cap (often referred to as "four-bolt mains" or "six-bolt mains" engines).

  6. General Motors LS-based small-block engine - Wikipedia

    en.wikipedia.org/wiki/General_Motors_LS-based...

    Displacement is 5,327 cc (5.3 L; 325.1 cu in) from a bore and stroke of 96 mm × 92 mm (3.78 in × 3.62 in). Vortec 5300s were built in St. Catharines, Ontario , and Romulus, Michigan . The aluminum block variants, the LM4 and the L33, share the same displacement, but instead use an aluminum block with cast-in cylinder liners, much like the LS1.

  7. Long-bolt engine - Wikipedia

    en.wikipedia.org/wiki/Long-bolt_engine

    A long-bolt or through-bolt engine is an internal combustion piston engine where, following usual practice, the cylinder head is held down by bolts or studs. Conventionally the cylinder head is bolted to the cylinder block and the crankshaft main bearings are in turn bolted to the crankcase by separate bolts.

  8. General Motors Atlas engine - Wikipedia

    en.wikipedia.org/wiki/General_Motors_Atlas_engine

    The LLR (also called Vortec 3700), is a straight-5 DOHC engine produced from 2007 through 2012. It displaces 3.7 L; 222.9 cu in (3,653 cc), courtesy of a larger 95.5 mm (3.76 in) bore while keeping the 102 mm (4.02 in) stroke. The LLR also corrected the head issue found in the L52.

  9. Straight-three engine - Wikipedia

    en.wikipedia.org/wiki/Straight-three_engine

    Circa-1960 Saab two-stroke engine 2010 Suzuki K10B engine. Among the first cars to use a straight-three engine is the 1953–1955 DKW F91, powered by a 900 cc (55 cu in) two-stroke engine, although this was predated by the 3 cylinder 15hp Rolls Royce produced in 1905 and a number of other cars of this era also used 3 cylinder engines.

  1. Ads

    related to: main lug only vs mlo 5 bolt lock set 3 speed engine