enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Preferred metric sizes - Wikipedia

   en.wikipedia.org/wiki/Preferred_metric_sizes

   Machine screws with different thread diameters Hex key set with metric sizes from 2 mm to 10 mm according to sizes for use with ISO 262 screw sizes (except 3.5 mm for M6 internal set screw) For each size bolt or screw and type of head, there is a corresponding size driver prescribed by various ISO standards, including: Internal hex drive: ISO ...

3. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25).

4. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   ISO general-purpose screw threads—Basic profile—Part 2: Inch screw threads: V Thread Form ISO 261:1998: ISO general purpose metric screw threads—General plan: V Thread Form: M6x1 ISO 262:1998: ISO general purpose metric screw threads—Selected sizes for screws, bolts and nuts: V Thread Form ISO 724:1993

5. List of screw drives - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_drives

   A hex screw drive uses six-sided fastener heads, and the fastener is known as a hex head cap screw. It can be turned with an adjustable wrench, combination wrench and 6- or 12-point sockets. The hex drive is better than square drive for locations where surrounding obstacles limit wrenching access, because smaller wrench-swing arcs can still ...

6. List of screw and bolt types - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_and_bolt_types

   In 1913, Woolley and Meredith defined them like Anthony, but gave the following dimensions: hex head cap screws up to and including 7 ⁄ 16 inch (11.1125 mm) have a head that is 3 ⁄ 16 inch (4.7625 mm) larger than the shank diameter; screws greater than 1 ⁄ 2 inch (12.7 mm) in diameter have a head that is 1 ⁄ 4 inch (6.35 mm) larger than ...

7. British Association screw threads - Wikipedia

   en.wikipedia.org/wiki/British_Association_screw...

   The major diameter is given by 6p 1.2, [4]: 12 rounded to two significant figures in mm and the hex head size (across the flats) is 1.75 times the major diameter. BA sizes are specified by the following British Standards: BS 57:1951 — B.A. screws, bolts and nuts

8. Computer case screws - Wikipedia

   en.wikipedia.org/wiki/Computer_case_screws

   All three patterns may also be combined with a slot for a flat-blade screwdriver. Usually they are provided with a 1/4 in (0.25 inches (6.4 mm)) flanged hex head. Non-standard metricized 5.5 millimetres (0.22 in) flanged hex heads can also be encountered. Also common are pan head screws - a low disk with a chamfered outer edge.

9. List of DIN standards - Wikipedia

   en.wikipedia.org/wiki/List_of_DIN_standards

   ISO general purpose metric screw threads – Part 2: Nominal sizes for 0,2 mm, 0,25 mm and 0,35 mm fine pitch threads; nominal diameter from 1 mm to 50 mm: Active: DIN 13-3: ISO general purpose metric screw threads – Part 3: Nominal sizes for 0,5 mm fine pitch threads; nominal diameter from 3,5 mm to 90 mm: Active: DIN 13-4