enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Preferred metric sizes - Wikipedia

   en.wikipedia.org/wiki/Preferred_metric_sizes

   Machine screws with different thread diameters Hex key set with metric sizes from 2 mm to 10 mm according to sizes for use with ISO 262 screw sizes (except 3.5 mm for M6 internal set screw) For each size bolt or screw and type of head, there is a corresponding size driver prescribed by various ISO standards, including: Internal hex drive: ISO ...

3. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   Hexagonal (generally abbreviated to "hex") head widths (width across flats, spanner size) are for DIN 934 hex nuts and hex head bolts. Other (usually smaller) sizes may occur to reduce weight or cost, including the small series flange bolts defined in ISO 4162 which typically have hexagonal head sizes corresponding to the smaller 1st choice ...

4. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   ISO general purpose metric screw threads—General plan: V Thread Form: M6x1 ISO 262:1998: ISO general purpose metric screw threads—Selected sizes for screws, bolts and nuts: V Thread Form ISO 724:1993: ISO general-purpose metric screw threads—Basic dimensions: V Thread Form ISO 725:2009: ISO inch screw threads—Basic dimensions: V Thread ...

5. List of screw and bolt types - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_and_bolt_types

   In 1913, Woolley and Meredith defined them like Anthony, but gave the following dimensions: hex head cap screws up to and including 7 ⁄ 16 inch (11.1125 mm) have a head that is 3 ⁄ 16 inch (4.7625 mm) larger than the shank diameter; screws greater than 1 ⁄ 2 inch (12.7 mm) in diameter have a head that is 1 ⁄ 4 inch (6.35 mm) larger than ...

6. List of screw drives - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_drives

   A hex screw drive uses six-sided fastener heads, and the fastener is known as a hex head cap screw. It can be turned with an adjustable wrench, combination wrench and 6- or 12-point sockets. The hex drive is better than square drive for locations where surrounding obstacles limit wrenching access, because smaller wrench-swing arcs can still ...

7. Computer case screws - Wikipedia

   en.wikipedia.org/wiki/Computer_case_screws

   All three patterns may also be combined with a slot for a flat-blade screwdriver. Usually they are provided with a 1/4 in (0.25 inches (6.4 mm)) flanged hex head. Non-standard metricized 5.5 millimetres (0.22 in) flanged hex heads can also be encountered. Also common are pan head screws - a low disk with a chamfered outer edge.

8. List of DIN standards - Wikipedia

   en.wikipedia.org/wiki/List_of_DIN_standards

   ISO general purpose metric screw threads – Part 2: Nominal sizes for 0,2 mm, 0,25 mm and 0,35 mm fine pitch threads; nominal diameter from 1 mm to 50 mm: Active: DIN 13-3: ISO general purpose metric screw threads – Part 3: Nominal sizes for 0,5 mm fine pitch threads; nominal diameter from 3,5 mm to 90 mm: Active: DIN 13-4

9. British Association screw threads - Wikipedia

   en.wikipedia.org/wiki/British_Association_screw...

   The major diameter is given by 6p 1.2, [4]: 12 rounded to two significant figures in mm and the hex head size (across the flats) is 1.75 times the major diameter. BA sizes are specified by the following British Standards: BS 57:1951 — B.A. screws, bolts and nuts