enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. Useful conversions and formulas for air dispersion modeling

    en.wikipedia.org/wiki/Useful_conversions_and...

    Atmospheric pollutant concentrations expressed as mass per unit volume of atmospheric air (e.g., mg/m 3, μg/m 3, etc.) at sea level will decrease with increasing altitude because the atmospheric pressure decreases with increasing altitude.

  3. Air pollutant concentrations - Wikipedia

    en.wikipedia.org/wiki/Air_pollutant_concentrations

    mg/m 3 = milligrams of pollutant per cubic meter of air at sea level atmospheric pressure and T: ppmv = air pollutant concentration, in parts per million by volume T = ambient temperature in K = 273. + °C 0.082057338 = Universal gas constant in L atm mol −1 K −1: M = molecular mass (or molecular weight) of the air pollutant

  4. Grain per gallon - Wikipedia

    en.wikipedia.org/wiki/Grain_per_gallon

    The grain per gallon (gpg) is a unit of water hardness defined as 1 grain (64.8 milligrams) of calcium carbonate dissolved in 1 US gallon of water (3.785412 L). It translates into 1 part in about 58,000 parts of water or 17.1 parts per million (ppm). Also called Clark degree (in terms of an imperial gallon).

  5. Parts-per notation - Wikipedia

    en.wikipedia.org/wiki/Parts-per_notation

    For example, the conversion factor between a mass fraction of 1 ppb and a mole fraction of 1 ppb is about 4.7 for the greenhouse gas CFC-11 in air (Molar mass of CFC-11 / Mean molar mass of air = 137.368 / 28.97 = 4.74). For volume fraction, the suffix "V" or "v" is sometimes appended to the parts-per notation (e.g. ppmV, ppbv, pptv).

  6. Total dissolved solids - Wikipedia

    en.wikipedia.org/wiki/Total_dissolved_solids

    where TDS is expressed in mg/L and EC is the electrical conductivity in microsiemens per centimeter at 25 °C. The conversion factor k e varies between 0.55 and 0.8. [5] Some TDS meters use an electrical conductivity measurement to the ppm using the above formula. Regarding units, 1 ppm indicates 1 mg of dissolved solids per 1,000 g of water. [6]

  7. Grain (unit) - Wikipedia

    en.wikipedia.org/wiki/Grain_(unit)

    [14] [15] Otherwise, water hardness is measured in the dimensionless unit of parts per million (ppm), numerically equivalent to concentration measured in milligrams per litre. [14] [15] One grain per U.S. gallon is approximately 17.1 ppm. [14] [note 1] Soft water contains 1–4 gpg of calcium carbonate equivalents, while hard water contains 11 ...

  8. Hard water - Wikipedia

    en.wikipedia.org/wiki/Hard_water

    Parts per million (ppm) is usually defined as 1 mg/L CaCO 3 (the definition used below). [20] It is equivalent to mg/L without chemical compound specified, and to American degree . Grain per gallon (gpg) is defined as 1 grain (64.8 mg) of calcium carbonate per U.S. gallon (3.79 litres), or 17.118 ppm.

  9. Drinking water quality standards - Wikipedia

    en.wikipedia.org/wiki/Drinking_water_quality...

    " indicates that no standard has been identified by editors of this article and ns indicates that no standard exists. μg/L = micrograms per litre, or 0.001 ppm; mg/L = 1 ppm, or 1000 μg/L. * means action level; not a concentration standard. A public water system exceeding the action level must implement "treatment techniques" which are ...