enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25). If the pitch is the normally used "coarse" pitch listed in ISO 261 or ...

3. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Example (inch, fine): For 7 ⁄ 16-20 (same diameter as the previous example, but this time with 20 threads per inch, which is considered fine), 0.437 in × 0.90 = 0.393 in (i.e., if the threads are to be fine, then a slightly larger diameter drill bit should be used before tapping the hole for the screw).

4. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   Metric Screw Threads - MJ Profile: V Thread Form BS 84: Tables of BS Whitworth, BS Fine and BS Pipe Threads: V Thread Form (55°) 1 ⁄ 4 ″-20 BSW ISO 68-1:1998: ISO general purpose screw threads—Basic profile—Part 1: Metric screw threads: V Thread Form ISO 68-2:1998: ISO general-purpose screw threads—Basic profile—Part 2: Inch screw ...

5. IEC metric screw sized connectors - Wikipedia

   en.wikipedia.org/wiki/IEC_metric_screw_sized...

   IEC metric screw sized connectors is a family of electrical connectors defined by IEC that are named according to their ISO metric screw thread, namely M5, M8 and M12. [1] The number gives their outer screw thread diameter in millimeters as with the identically named screws.

6. ISO 965 - Wikipedia

   en.wikipedia.org/wiki/ISO_965

   ISO 965 (ISO general purpose metric screw thread—tolerances) is an International Organization for Standardization (ISO) standard for metric screw thread tolerances. [1] It specifies the basic profile for ISO general purpose metric screw threads (M) conforming to ISO 261. [2] The tolerance system refers to the basic profile in accordance with ...

7. Preferred metric sizes - Wikipedia

   en.wikipedia.org/wiki/Preferred_metric_sizes

   Machine screws with different thread diameters Hex key set with metric sizes from 2 mm to 10 mm according to sizes for use with ISO 262 screw sizes (except 3.5 mm for M6 internal set screw) For each size bolt or screw and type of head, there is a corresponding size driver prescribed by various ISO standards, including: Internal hex drive: ISO ...

8. List of DIN standards - Wikipedia

   en.wikipedia.org/wiki/List_of_DIN_standards

   Self-drilling screws with tapping screw thread – Dimensions, requirements and testing: Withdrawn: ISO 10666, ISO 15480, ISO 15481, ISO 15482, ISO 15483: DIN 7513: Hexagon head and slotted head thread cutting screws – Dimensions, requirements and testing: Active: DIN 7516: Cross recessed head thread cutting screws – Dimensions ...

9. Width across flats - Wikipedia

   en.wikipedia.org/wiki/Width_across_flats

   A few sizes are close enough to interchange for most purposes, such as 19 mm (close to 3 ⁄ 4 inch (19.05 mm)), 8 mm (close to 5 ⁄ 16 inch (7.94 mm)) and 4 mm (close to 5 ⁄ 32 inch (3.97 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.