enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. File:Mm to 1 inch fraction ruler.svg - Wikipedia

   en.wikipedia.org/wiki/File:Mm_to_1_inch_fraction...

   English: a ruler from 0 to 1 inch (in.) in 1/32 inch divisions below the line and 1/2 millimetre (mm) divisions above the line to give a visual representation of the approximations. Principally designed to help visually determine if a metric or imperial drill bit will suffice.

3. Millimetre - Wikipedia

   en.wikipedia.org/wiki/Millimetre

   Different lengths as in respect to the electromagnetic spectrum, measured by the metre and its derived scales.The microwave is between 1 meter to 1 millimeter.. The millimetre (international spelling; SI unit symbol mm) or millimeter (American spelling) is a unit of length in the International System of Units (SI), equal to one thousandth of a metre, which is the SI base unit of length.

4. List of scale model sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_scale_model_sizes

   Original nominal 25 mm figure scale; though a 6-foot human in 1:87 is closer to 21 mm. 1:82: 3.717 mm An intermediate scale (HO/OO) intended to apply to both HO and OO scale train sets. Also used for some military models 1:80: 3.810 mm HOj scale. Very close to wargaming 20 mm figure scale (20 mm is actually 1:80.5). [10] 1:76.2: 4 mm

5. Orders of magnitude (length) - Wikipedia

   en.wikipedia.org/wiki/Orders_of_magnitude_(length)

   To help compare different orders of magnitude, this section lists lengths between 10 −3 m and 10 −2 m (1 mm and 1 cm). 1.0 mm – 1/1,000 of a meter; 1.0 mm – 0.03937 inches or 5/127 (exactly) 1.0 mm – side of a square of area 1 mm²; 1.0 mm – diameter of a pinhead; 1.5 mm – average length of a flea [27]

6. Unit of length - Wikipedia

   en.wikipedia.org/wiki/Unit_of_length

   A ruler, depicting two customary units of length, the centimeter and the inch. A unit of length refers to any arbitrarily chosen and accepted reference standard for measurement of length. The most common units in modern use are the metric units, used in every country globally.

7. Graduation (scale) - Wikipedia

   en.wikipedia.org/wiki/Graduation_(scale)

   A ruler with two linear scales: the metric and imperial.It includes shorter minor graduations and longer major graduations. A graduation is a marking used to indicate points on a visual scale, which can be present on a container, a measuring device, or the axes of a line plot, usually one of many along a line or curve, each in the form of short line segments perpendicular to the line or curve.

8. Point (typography) - Wikipedia

   en.wikipedia.org/wiki/Point_(typography)

   A less precise definition is one pica equals 0.166 inches (4.2 mm), and one point 0.01383 inches (0.351 mm). [27] [33] It was also noticed that 83 picas is nearly equal to 35 cm, so the Type Founders Association also suggested using a 35 cm metal rod for measurements, but this was not accepted by every foundry. [27]

9. Width across flats - Wikipedia

   en.wikipedia.org/wiki/Wrench_size

   A few sizes are close enough to interchange for most purposes, such as 19 mm (close to 3 ⁄ 4 inch (19.05 mm)), 8 mm (close to 5 ⁄ 16 inch (7.94 mm)) and 4 mm (close to 5 ⁄ 32 inch (3.97 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.